Wheels

Reliable, simple, and e-bike specific hub. To withstand the higher torque of e-drive systems, the 350 hybrid is equipped with steel rotors and a specific 24T ratchet out of hardened steel. Oversized bearings ensure smooth running under extreme conditions.

When motor assistance and leg power meet, the range of terrain a bike can conquer grows almost exponentially. The H 1900 SPLINE is designed for this, now upgraded with the famous DT Swiss Ratchet technology. The Ratchet LN system distributes the combined forces from the rider and the motor over a larger area than the previous pawl freehub systems, increasing the systems’ durability thanks to lower load peaks. The 370 hub enables full power transmission to the ground with reinforced hybrid spokes laced to a resistant aluminum rim, available in two inner widths. - Aluminum rim, Hooked / Crotchet tubeless ready - DT Hybrid 1 spokes are reinforced and increase the lateral and torsional stiffness of the wheel - 370 Hub - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

The HXC 1501 SPLINE ONE LS are extra lightweight carbon eMTB wheels are engineered for riders looking for outstanding agility. Thanks to the low weight carbon rims, riders benefit from increased agility and dynamism when going uphill and downhill, while withstanding the increased torques of eMTBs. The spokes were designed with specific diameters to align light weight and resistance. Inside the 240 hub, oversized bearings support the additional loads of eMTBs. Each component has been designed with the specific aim of delivering advanced agility to find flow and fun on the trails. - Built to provide ultimate riding agility for light eMTBs - Perfect balance between low weight and resistance, ready to go faster in the ups and the downs - Hybrid-specific spoke design provides an advanced riding experience, combining resistance and lightweight - The 240 Hybrid LS hub features larger bearings for improved durability and rolling efficiency

The HXC 1501 SPLINE ONE LS are extra lightweight carbon eMTB wheels are engineered for riders looking for outstanding agility. Thanks to the low weight carbon rims, riders benefit from increased agility and dynamism when going uphill and downhill, while withstanding the increased torques of eMTBs. The spokes were designed with specific diameters to align light weight and resistance. Inside the 240 hub, oversized bearings support the additional loads of eMTBs. Each component has been designed with the specific aim of delivering advanced agility to find flow and fun on the trails. - Built to provide ultimate riding agility for light eMTBs - Perfect balance between low weight and resistance, ready to go faster in the ups and the downs - Hybrid-specific spoke design provides an advanced riding experience, combining resistance and lightweight - The 240 Hybrid LS hub features larger bearings for improved durability and rolling efficiency - Ratchet EXP OS, optimized for the requirements of an eMTB, with a bigger threaded ring for direct acceleration through a torque-resistant freehub system

After a long climb, the perfect trail lies ahead of your tires: flowy, dusty, varied, endless. Nothing holds you back from entering the All-Mountain thrills with the M 1900 Spline wheels. A rim developed with optimal balance of durability and weight offers efficient climbing characteristics as well as dent resistance on single trails. With experienced wheel building by hand, this wheel is a reliable partner to collect freewheeling moments in the mountains. - Intended use = XC and All-Mountain/Trail - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

- Kits include one pair of end caps - Instructions and hub axle determinations are available online @ www.notubes.com

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

Champion 2.0 Black Spokes - One 264mm spoke = 7g

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

Getting the correctly sized magnets means you're worrying about where the next coffee stop is, not if your computer is recording the ride. Key features: - Universal wheel magnets work with any speed sensor - Thread-on speed magnet is positioned closer to the sensor for improved signal - Aero speed magnet provides a sleek, low-profile, aerodynamic solution

Upgrade or refresh your Bontrager wheels. Product details - Replacement, high-quality rim strips that help prevent flat tires - Compatible with nearly all common wheels - Width refers to internal rim dimension - Not Tubeless Ready - Sold as singles

Salsa springs for Flip-Off skewers

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Tubeless setup made easy with valve stems designed to work as a system with Bontrager wheels, tires and rim strips The valves you need to upgrade to Tubeless These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Use only with Bontrager TLR rim strip with rectangular base - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Sold as singles

The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples

This rim tape is crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Tape is designed for wider Plus and Fat wheels - Can also be used as a universal tubeless solution for non-Bontrager rims - Use only with Bontrager TLR rim valve with round base - Rim tape replacement is recommended if removed from the wheel - One roll is 5m (197") in length

- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.

- To be used exclusively with Bontrager 29""/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel

- To be used exclusively with Bontrager 29""/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

To be used exclusively with Bontrager Tubeless Ready (TLR) rims. The rim strips you need to upgrade to Tubeless These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Use only with appropriate Bontrager TLR rim valve - Rim strip replacement is recommended if removed from the wheel - Sold as singles - White strip is recommended for carbon rims - TLR rim valve sold separately

These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel - For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.